Free · runs in your browser

Audio latency and sync test

Measure your audio delay two ways: time real clicks through your speakers and microphone, or line up a flash and a beep by eye to find how far your sound lags the picture.

  • Round trip in ms
  • AV sync by eye
  • Wired vs Bluetooth

Measure the round trip

Use speakers, not headphones (or hold the microphone against an earcup). Turn the volume to about half and keep the room quiet.

Round trip—
Spread—
Clicks found—
Browser reports—

Plays 10 short clicks and listens for them with your microphone. Nothing is recorded.

Check audio and video sync

No microphone needed, so it works with Bluetooth headphones, soundbars and TVs. Press Start, watch the flash and listen to the beep, then move the slider until they happen together.

Delay the picture
Picture delayed by0 ms
Your sound is—

Beeps once a second. Start with your volume low.

Confirming
Latency test

To: Your speakers + microphone · via your browser

Date—
Rate—
Clicks—
Reported—
Round tripNot tested
SpreadNot tested
VerdictNot tested
Sound vs pictureNot tested
audiotesthq.com

Your result appears here as you answer. Nothing is uploaded.

More tests: follow the sign

An audio latency test measures the delay between your device sending a sound and that sound actually coming out. This one plays 10 short clicks through your speakers, listens for them with your microphone, and times each one. The result is your round-trip latency in milliseconds: output delay, plus input delay, plus the time sound takes to cross the air.

How to read your result

Round tripWhat you will notice
Under 30 msVery low. Good for playing an instrument through the computer.
30–100 msLow. Fine for calls, video and most games.
100–200 msNoticeable. Lip sync can look slightly off; rhythm games feel late.
Over 200 msHigh. Common with Bluetooth; video may need an audio-delay setting.

These bands are a practical guide, not a standard. Because this is a round trip, your one-way playback delay is roughly half or less, depending on your microphone.

What is included in the number

  • Output: the browser, operating system, driver and device (Bluetooth adds the most).
  • Air: about 3 ms for every metre between speaker and microphone, because sound travels at roughly 343 metres a second.
  • Input: the microphone, its driver and the browser.

The Browser reports figure is the browser's own estimate of its output delay. It often misses the device's share, which is why the measured round trip is usually higher.

Testing Bluetooth headphones

Bluetooth headphones do not leak enough sound into your microphone for this test. Hold your phone or laptop microphone right against one earcup, set the volume to about half, and run it. Compare with wired headphones or speakers to see how much the Bluetooth link adds.

Checking audio and video sync

The second panel finds how far your sound lags behind the picture, which is what you notice as bad lip sync. It plays a beep once a second and flashes the box at the same moment. If your speakers or headphones add delay, you hear the beep after the flash. Move the slider to delay the flash until both happen together; the slider then shows how many milliseconds your sound is late. Because your screen's own delay is included, this is the number a TV or player's audio delay or lip sync setting needs.

  • Watch the dot: it crosses the centre line at the moment of the flash, which makes the timing easier to judge.
  • Go past the point where they match, come back, and repeat a few times. Most people can judge it to within a few tens of milliseconds.
  • The flash can only change when your screen refreshes, about every 17 ms on a 60 Hz screen.

How much delay can you see?

ITU-R Recommendation BT.1359-1, the broadcasting standard for the relative timing of sound and vision, reports that on average viewers start to detect an error when sound is about 45 ms early or 125 ms late, and find it unacceptable at about 90 ms early or 185 ms late. Late sound is tolerated more than early sound.

Your sound isITU-R BT.1359-1, on average
Up to 125 ms late, or up to 45 ms earlyNot detected
125–185 ms late, or 45–90 ms earlyDetectable
More than 185 ms late, or more than 90 ms earlyUnacceptable

Thresholds from subjective tests on television material; individual viewers differ.

Reducing latency

  • Use a wired connection instead of Bluetooth where timing matters.
  • Close other apps using audio; some add processing.
  • On TVs and receivers, look for a game mode or an audio delay (lip sync) setting, and set it to the number the sync check gave you.

Common questions

How do I test audio delay?

Press Measure my latency with your speakers on and the room quiet. The test plays 10 clicks and times them through your microphone.

Why can't the test find the clicks?

The microphone did not hear them clearly. Turn the volume up, use speakers rather than headphones, move the microphone closer, and switch off noise-cancelling software.

What is a good audio latency?

For calls and video, under about 100 ms round trip is comfortable. Musicians playing live through a computer usually want under 30 ms.

Is Bluetooth latency always high?

Bluetooth usually adds more delay than a wired connection, and the amount varies by device and codec. Measure it rather than guessing.

How do I test audio and video sync?

Use the sync check: press Start, watch the flash and listen to the beep, and move the slider until they happen together. The slider shows how many milliseconds your sound lags the picture.

How much lip sync delay is noticeable?

ITU-R BT.1359-1 reports that viewers on average notice sound about 125 ms late or 45 ms early, and find it unacceptable at about 185 ms late or 90 ms early.

Last reviewed 14 November 2026 by Sri Murugan Systems. Found a mistake? Tell us.